From the monthly archives:

August 2018

Universal 6 Gallon Aluminum EFI Gas Tank

$516.00

{ 0 comments }

Universal 22 Gallon Aluminum EFI Tank W/ Sender

$742.00

{ 0 comments }

Universal Gallon Aluminum EFI Tank W/ Sender

$653.00

{ 0 comments }

Universal 12 Gallon Aluminum EFI Tank W/ Sender

$612.00

{ 0 comments }

Universal 12 Gallon Aluminum EFI Tank

$590.00

{ 0 comments }

Dimensions = 26.125″L x 20.125″w x 17.375″T
Material = .190 5052 mill aluminum
2″ OD Fill pipe
1/2″ NPT Vent

Fits in the stock location using all stock pump and components

$675.00

{ 0 comments }

Dimensions = 23 x 20.5 x 17.190
Material = .190 5052 mill aluminum
2″ OD Fill pipe
1/2″ NPT Vent

Fits in the stock location using all stock pump and components

$575.00

{ 0 comments }

Ford F53 Chassis Motorhome Replacement Aluminum Tank

$1,200.00

{ 0 comments }

Ford F Series Aluminum Weld-in OEM Vent Bung

$24.99

{ 0 comments }

8 Gallon Aluminum Universal Fuel Tank

$150.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: The dimensions vary to match the contour of the frame

Q: How Tall is the fill neck?

A: The fill neck is approx 3″ tall.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI?

A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.

$369.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: The dimensions vary to match the contour of the frame

Q: How Tall is the fill neck?

A: The fill neck is approx 3″ tall.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI?

A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.

$369.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: The dimensions vary to match the contour of the frame

Q: How Tall is the fill neck?

A: The fill neck is approx 3″ tall.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

$951.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: The dimensions vary to match the contour of the frame

Q: How Tall is the fill neck?

A: The fill neck is approx 3.5″ tall.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

$686.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: The dimensions vary to match the contour of the frame

Q: How Tall is the fill neck?

A: The fill neck is approx 3″ tall.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

$686.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: 3″ down from the top of the tank

Q: How Tall is the fill neck? What is the Diameter of the pipe?

A: The fill neck is approx 3″ tall. The pipe is 2″ OD

Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?

A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI?

A: Yes, We have designed our tank with the EFI provision and baffeling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.

Q: Will this tank fit my 63-66?

A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges.

Q: I have a Blazer, can i use this tank?

A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.


$369.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: 3″ down from the top of the tank

Q: How Tall is the fill neck?

A: The fill neck is approx 3″ tall.

Q: Will the fill cap stick through my bed floor?
A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank.

Q: What do i get if i choose the Flush Floor Fill?
A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?
A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI?
A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.

Q: Will this tank fit my 63-66?
A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges.

Q: I have a Blazer, can i use this tank?
A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$369.00

{ 0 comments }

Frequently Asked Questions:

Q: How Far down are the mounting tabs?
A: 3″ down from the top of the tank

Q: How Tall is the fill neck?

A: The fill neck with cap is approx 3″ tall.
Q: Will the fill cap stick through my bed floor?
A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank.

Q: What do i get if i choose the Flush Floor Fill?
A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill.


Q: Are there Baffles in the Tank?
A: Yes, There are 3 baffles in the tank.

Q: What is the Roll Over Safety Vent? Do i need it?
A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.

Q: Will this tank fit my 63-66?
A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges.

Q: I have a Blazer, can i use this tank?
A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.

$686.00

{ 0 comments }

Boyd Welding 2″ Machined Cap & Neck

{ 0 comments }