| Universal 6 Gallon Aluminum EFI Gas Tank
$516.00
|
{ 0 comments }
Posts by author:
admin
| Dimensions = 26.125″L x 20.125″w x 17.375″T Material = .190 5052 mill aluminum 2″ OD Fill pipe 1/2″ NPT Vent Fits in the stock location using all stock pump and components
$675.00
|
{ 0 comments }
| Dimensions = 23 x 20.5 x 17.190 Material = .190 5052 mill aluminum 2″ OD Fill pipe 1/2″ NPT Vent Fits in the stock location using all stock pump and components
$575.00
|
{ 0 comments }
|
Frequently Asked Questions: Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.
$369.00
|
{ 0 comments }
|
Frequently Asked Questions: Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware.
$369.00
|
{ 0 comments }
|
Frequently Asked Questions: Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.
$951.00
|
{ 0 comments }
|
Frequently Asked Questions: Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3.5″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.
$686.00
|
{ 0 comments }
|
Frequently Asked Questions: Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option.
$686.00
|
{ 0 comments }
|
Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? What is the Diameter of the pipe? A: The fill neck is approx 3″ tall. The pipe is 2″ ODQ: Are there Baffles in the Tank? A: Yes, There are 3 baffles in the tank. Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffeling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$369.00
|
{ 0 comments }
|
Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.Q: Will the fill cap stick through my bed floor? A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank. Q: What do i get if i choose the Flush Floor Fill? A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill. Q: Are there Baffles in the Tank? A: Yes, There are 3 baffles in the tank. Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$369.00
|
{ 0 comments }
|
Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck with cap is approx 3″ tall. Q: Will the fill cap stick through my bed floor?A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank. Q: What do i get if i choose the Flush Floor Fill? A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill. Q: Are there Baffles in the Tank? A: Yes, There are 3 baffles in the tank. Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$686.00
|
{ 0 comments }
|
PRODUCT # 25018-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-18) Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$67.93
|
{ 0 comments }
|
PRODUCT # 25018-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-12) Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$59.06
|
{ 0 comments }
|
PRODUCT # 25018-06 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-06) Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$50.19
|
{ 0 comments }
|
PRODUCT # 25016-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 -.312 +/- (Need a Bigger tube? See SKU# 25018-06) Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$46.19
|
{ 0 comments }
|
PRODUCT # 25016-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$70.54
|
{ 0 comments }
|
PRODUCT # 25016-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$65.67
|
{ 0 comments }
|
PRODUCT # 25016-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$60.80
|
{ 0 comments }
|
PRODUCT # 25016-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$55.93
|
{ 0 comments }
|
PRODUCT # 25016-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$51.06
|
{ 0 comments }
|
Product # 44033
Material: 5052 Aluminum
OD: 6″
ID: 4.375″
Bolt CL : 5.25″
Installed Height: .250 +/-
Threads: 10-32 Zinc Plated Threadsert
Harware Included: YES
Gasket: YES
Cover Plate Thickness: .125″ (1/8″)
Bolt in Assembly, No Welding needed.
Will work with any type of tank, Aluminum, Plastic, Steel or Stainless
This product is for use on the top of tank only.
$38.57
|
{ 0 comments }
|
SKU# WBRKT-300
- ALUMINUM CONSTRUCTION
- CHAIN INCLUDED
- SINGLE BOTTLE
- HOOK HOLES FOR WRENCH
Dimensions:
14.5″ Long
6″ Wide ( sticks out from wall)
Bottle Diameter = 9.25″ (Standard 300CF welding bottle)
Mounts to any type of wall. Mounting hardware NOT included.
$36.00
|
{ 0 comments }
|
Product # 46002
Replacement Boyd Welding Tank Cleanout Gasket 8 Bolt
Material: BUNA- N
Thickness: .125″
OD: 6″
ID: 4.375″
x8 .250 holes on 5.25″ BCL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$9.25
|
{ 0 comments }
|
Product Number: 14046 WILL FIT YEARS 60-62 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: This product is in-stock but may take up to 5 days for shipment. -Tank Dimensions: 35.5 x 19 x 10 **Scroll down for FAQ on this product.
$699.00
|
{ 0 comments }
|
Product Number: 14044 WILL FIT YEARS 60-62 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: This product is in-stock but may take up to 5 days for shipment. -Tank Dimensions: 35.5 x 19 x 10 **Scroll down for FAQ on this product.
$399.00
|
{ 0 comments }
Boyd, Good morning
Just wanted to share with you how pleased I am with the new gas tank for my 1957 Chevy stepside. You definitely produce a top quality product.
I was so close to buying that ugly ass box that LMC has only because while searching the google search LMC and brothers were the top hits. (And we have to change that)
I was at a friends house looking at his 66 Chevy truck build and he had one of your tanks installed.
I’m old school and do not use Facebook for social media but have seen yours. Boyd’s welding looks like a thriving company and you probably don’t need my accolades. But I shared a shout out with my friends at Tri-Five truck forum and 49-67 Truck forum. Hopefully that will get your name to the top of the google search.
I’m a retired union pipe fitter out of local 150 Augusta, Georgia and have a eye for quality craftsmanship and top notch welding.
Just wanted to put your name out there, would have sent you the links but couldn’t figure out how with the I pad (old people with electronic gadgets) Lol !!!
Thanks again, JT
{ Comments on this entry are closed }
I just received my tank from you guys yesterday, and I wanted to personally send you an email about the quality. I am a certified TIG welder, I’m in the automotive field myself. It’s very hard to find a product that doesn’t arrive at the door needing to be modified or “fixed”. When I opened the box, I couldn’t believe what I saw…thank you for taking pride in what you do, unbelievable quality and finish!! I don’t think I have ever been so impressed by the quality and welding on any part I have ordered since I have been in the business! Thanks again!!!
Jesse
P.s. it’s also very impressive that it was delivered on the exact anticipated ship date, I received the email without having to send one first, you run a business that is rare for today’s standards, keep it up man!!! Awesome!
{ Comments on this entry are closed }
|
Product #27042
Cap: Neck: -Bolt- IN - Hole Cut Size = 3.760″ MIN / 3.950″ MAX (3-3/4″ hole saw) - Bolt hole Center = 4.350″ Kit Includes: - 1) CNC Machined CAP W/ Oring and Delrin Key - 1) CNC Machined flush bed fill neck 2″ RFH - 1) 4″ Long 2″ID Fuel Fill Hose - 2) Stainless worm clamps ( Optional components based on selection below) ****Hardware to mount to your bed floor not included***** FAQ: Q: What size hose does this use? A: The ribbed part of this neck is 2″ so you will need to purchase 2″ ID Fuel fill hose. We sell this in 3′ lengths SKU# 37015 Q:I already purchased a bed fill C-10 tank with a Boyd cap, will this work with what I already have? A: Yes, you will need to select “Yes” below so we can provide extra parts in this kit to adapt the Flush Bed fill to the threaded neck. The procedure to make this work is outlined in the instructions provided.
$99.75
|
{ 0 comments }
|
Product # 44032
Material = CNC Machined 6061-T6 OD= 6.00″ ID= 3.510″ Height = 0.500″ Installed height without pump = 0.625″ Bolt Circle A (BW EFI) = x12 @ 5.00″ BCL Bolt Circle B (Aeromotive) = x10 10-32 @ 4.00″ BCL This CNC machined aluminum adater will allow you to adapt any Aeromotive phantom, A1000 or Eliminator in tank pump that utilizes the 10 bolt pattern to the Boyd Welding 12 bolt pattern. Kit Includes: 1) CNC Machined Adapter Plate 1) BW EFI Buna Gasket 12) 10-32 1″ Stanless Screws (BW Pattern) 10) 10-32 3/4″ Stainlss Screws ( Aeromotive Pattern) You will use the gasket and nylon washers that was supplied with the aeromotive pump you purchased. do not try to use the screws supplied with Aeromotive pumps.
$58.00
|
{ 0 comments }
|
Product #27041
Cap: Neck: -Bolt- IN - Overall Installed Height W/ Cap = .210″ - Hole Cut Size = 3.760″ MIN / 3.950″ MAX - Bolt hole Center = 4.350″ Kit Includes: - 1 CAP W/ Oring and Delrin Key - 1 Bolt In Neck - 1 Buna Gasket - 1 Under Ring W/10-32 thread serts - 8 SS 10-32 Flat Head Machine Screw
$89.75
|
{ 0 comments }
|
Product # 21030
This Item is sold individually. The QTY of items you place in your cart will be the QTY of Boss’s you recieve. For example if you need 15 fittings make sure to add QTY 15 to your cart.
Material: 6061 Aluminum CNC Machined OD(A): 1.00” +/- OD (B): .730” +/- Flange Thickness: .250” +/- Overall Length = 1.00” +/- Installed height= .250” +/- Threads: 5/16-18 / 3/8-16 / 1/2-13 Choose Options Below Tank Hole Cut Size: .730”MIN / 1.00” MAX -This fitting must be welded in -This fitting is threaded blind so there will be no need to seal the threads -This will provide threaded provisions in your assembly perfect for bolting steps, enclosures and other components. - Could be welded to the inside of a tank to provide a perfectly flush threaded fitting that wont leak.
$5.75
|
{ 0 comments }
|
Product # 21029
This Item is sold individually. The QTY of items you place in your cart will be the QTY of Boss’s you recieve. For example if you need 15 fittings make sure to add QTY 15 to your cart. Material: 6061 Aluminum CNC Machined OD(A): .500” +/- OD (B): .375” +/- Flange Thickness: .250” +/- Overall Length = .750” +/- Installed height= .250” +/- Threads: 10-24 / 10-32 / 1/4-20 Choose Options Below Tank Hole Cut Size: .375”MIN / .500” MAX -This fitting must be welded in -This fitting is threaded blind so there will be no need to seal the threads -This will provide threaded provisions in your assembly perfect for bolting steps, enclosures and other components. - Could be welded to the inside of a tank to provide a perfectly flush threaded fitting that wont leak.
$4.75
|
{ 0 comments }
|
Product # 44027 Material = CNC Machined 6061 Aluminum ID = 1.715″ +/- This adapter will thread into an existing female 2″ NPT and allow you to install a 5 bolt fuel level sending unit. Any of our sending units in our “sending unit” section will
$45.00
|
{ 0 comments }
|
Product # 81050 Material = STAINLESS STEEL ID = 1.970″ +/- NPSM = (NATIONAL PIPE STRAIGHT MECHANICAL)
$31.00
|
{ 0 comments }
|
Product # 81004 Material = Aluminum ID = 1.970″ +/- NPSM = (NATIONAL PIPE STRAIGHT MECHANICAL)
$22.00
|
{ 0 comments }
|
Product Number: 27027
Fits Kelch 2-1/4″ Caps
OD of Neck= 2.200″
ID of Neck = 1.75″
Overall height installed= 1.25″
Threads= 5TPI Modified Butress
Hole Cut = 2″ MIN 2.25″ MAX
Aluminum Weld-in Neck ( Steel, Stainless Steel Availible below)
$26.00
|
{ 0 comments }
|
Product # 44030
Material = CNC Machined 6061 Aluminum Overall Length = 3.00″ +/- Overall Diameter = 1.500″ +/- Hole Cut = 1.275″ -0.00 / +.015″ Approx Weight = 2.2 OZ -This Valve will work with water, gasoline or diesel fuel. -Use this valve any time it is important to trap fuel around a pump or pickup tube. -It may be necessary to use multiple valves - if installing this valve into an existing tank you must have access to both sides of the baffle. Examples of use would include but not limited to: -Off Road -Drag Racing -Road Racing -Marine Click video below for demonstration of this product.
$62.00
|
{ 0 comments }
|
PRODUCT # 00BTWW 4.3oz 60% Ring Spun Cotton 40% Polyester Color and Size Options Below T-SHIRTS ARE CURRENTLY ON ORDER AND SHOULD BE RECEIVED MAY 2016.
$20.00
|
{ 0 comments }
|
PRODUCT # BOYD-TIGWELDER 4.3oz 60% Ring Spun Cotton 40% Polyester Color and Size Options Below T-SHIRTS ARE CURRENTLY ON ORDER AND SHOULD BE RECEIVED MAY 2016.
$20.00
|
{ 0 comments }
|
SpinSecure FSS 754 Versalock Vented Female Cap
Product SKU # 81047 Vented = YES Keys Included= YES Connection= 2″ Male required on tank or use # 81048 Adapter This is for the CAP ONLY if you are building an aluminum tank you will need the following additional items. QTY 1) ( SKU # 21009) 2″ NPT Female QTY 1) (SKU # 81048) SpinSecure Male to Male Adapter
$49.50
|
{ 0 comments }
|
PRODUCT # 25017-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$86.04
|
{ 0 comments }
|
PRODUCT # 25017-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$81.17
|
{ 0 comments }
|
PRODUCT # 25017-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$76.30
|
{ 0 comments }
|
PRODUCT # 25017-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$71.43
|
{ 0 comments }
|
PRODUCT # 25017-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$66.56
|
{ 0 comments }
|
PRODUCT # 25017-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$61.69
|
{ 0 comments }
|
PRODUCT # 25016-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$70.54
|
{ 0 comments }
|
PRODUCT # 25016-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$65.67
|
{ 0 comments }
|
PRODUCT # 25016-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$60.80
|
{ 0 comments }
|
PRODUCT # 25016-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$46.19
|
{ 0 comments }
|
PRODUCT # 25016-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$55.93
|
{ 0 comments }
|
PRODUCT # 25016-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$51.06
|
{ 0 comments }
|
Boyd Welding 2″ Machined Cap & Neck - Weld-in application -Machined From 6061-T6 Aluminum -2″ Pipe Straight Thread 11.5 TPI - Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard *** 4″ Long and 6″ Long Necks are availible, choose option below before adding to cart.***
$49.75
|
{ 0 comments }
|
Product # 27046
Kelch Target 350 (VENTED) Cap and Aluminum Machined Neck
Cap:
-Material = Black Plastic
- Threads = 5 TPI Modified AM Butress
-Vented= Yes
-Lanyard = No
Neck:
- Material= 6061 Aluminum CNC Machined
- Threads= 5 TPI Modified AM Butress
- OD = 3.480″ +/-
- ID = 2.750″ +/-
-installed height (neck only) = 1.800″ +/-
Installation:
- MUST BE WELDED IN
- Overall Installed Height W/ Cap = 2.625″ +/-
- Hole Cut Size = 3.250″ +.065 / – Zero
$65.00
|
{ 0 comments }
Hi Dave,
I just wanted drop you note to say thanks, the tank arrived today and it was exactly what I had ordered (which doesn’t happen very often these days) The workmanship is excellent and the tank arrived on time and at a competitive price.
Thanks again
G.L – California
{ Comments on this entry are closed }
|
Product # 46005
Replacement SAE 5 Bolt Sending Unit Flange Gasket
Material: BUNA- N
Thickness: .125″ +/-
OD: 2.75″”
ID: 1.525″
x5 bolt pattern on 1.060 Bolt CL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$3.42
|
{ 0 comments }
|
Product # 46004
Replacement Boyd Welding EFI Gasket.
Material: BUNA- N
Thickness: .125″
OD: 6″
ID: 4″
x12 .190 holes on 5″ CL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$11.99
|
{ 0 comments }
|
Product Number: 27031
$69.00
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1.5″ Taper Plug W/Pull Ring Product # 74015 Fits Female 1.5″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.54
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1.25″ Taper Plug W/Pull Ring Product # 74014 Fits Female 1.25″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.42
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 3/8″ Taper Plug W/Pull Ring Product # 74010 Fits Female 3/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.24
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 3/4″ Taper Plug W/Pull Ring Product # 74012 Fits Female 3/4″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.30
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/2″ Taper Plug W/Pull Ring Product # 74011 Fits Female 1/2″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.24
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1″ Taper Plug W/Pull Ring Product # 74013 Fits Female 1″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.42
|
{ 0 comments }
Product # 21056 Material: 6061 Aluminum OD: 3" +/- ID: 2" +/- Flange Thickness: .250 Threads: UNF 10-32 Bolt Centerline: 6 x 2.375" CL Tank Hole Cut Size: 2.625" This Flange Fits most 6 bolt sending unit's usually found on british made vehicles IE: Morgan , Triumph , MG, ETC.
$18.25
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/8″ Taper Plug W/Pull Ring Product # 74008 Fits Female 1/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.18
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/8″ Taper Plug W/Pull Ring Product # 74009 Fits Female 1/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.18
|
{ 0 comments }
|
Product # 21057 Material: 6061 Aluminum OD: 2.5″ Installed Height: .875″ +/- Hole Size Needed: 2.25″ Fitting Threads: 1/4″ NPT Finish: Natural Machined Finish ** This sump must be welded into an aluminum tank only
$41.00
|
{ 0 comments }
|
Product # 44024 Material: Aluminum 6061-T6 Machined Dimensions Outside: 3 x 2 x .75 without fitting Thread: 3/8 NPT Weldable: YES
$29.00
|
{ 0 comments }
|
Product # 32008 Material: Aluminum 6061-T6 Machined Hose Size: 5/8″ Overall Lenght: 3″ Ouside Diameter: Approx 1″
$75.00
|
{ 0 comments }
|
Product # 27036 Cap and Neck included NECK: Material: Aluminum OD: Approx 2.375″ ID: Approx 1.75″ Threads : 2.25″ – 5 TPI Modified Butress Hole Cut : 2″ Overall Height with cap installed: 2.680″ Lanyard Length: Internal 8″
$49.00
|
{ 0 comments }
|
Ford F Series Weld-in OEM Vent Bung Aluminum Bung Only (OEM Vent Picutred-Not Included)
$24.99
|
{ 0 comments }
|
Product # 44022 Material: 6061 t-6 Aluminum OD: 6″ ID: 4.375″ Installed Height: .875″ Hole Cutout: 5.75″ Threads: 1/4-20 Blind Tapped Gasket: YES MUST BE WELDED IN
$59.00
|
{ 0 comments }
| 3 Port 1/2″ NPT Threaded Flange Machined from 6061 Aluminum Installed height .875″ Overall Dimensions 4.5″ x 4.5″
$35.00
|
{ 0 comments }
| 2 Port 1/2″ NPT Threaded Flange Machined from 6061 Aluminum Installed height .875″ Overall Dimensions 2″ x 4.5″
$28.50
|
{ 0 comments }
|
PRODUCT # 24011 Material = 6061 T-6 Aluminum Hole size = 9/16″ Slot Sold in Packs of QTY 4 These tabs are machined from a solid block of aluminum.
$88.00
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
| Boyd Welding 2″ Machined Knurled Cap & Neck
-Machined From 6061-T6 Aluminum -2″ Pipe Straigh Thread 11.5 TPI - NON Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard
Regular Price:
Special Price: |
{ 0 comments }
| Boyd Welding 2″ Machined Cap & Neck
-Machined From 6061-T6 Aluminum -2″ Pipe Straigh Thread 11.5 TPI - NON Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard
Regular Price:
Special Price: |
{ 0 comments }
|
Product # 26007 Material= CNC Machined from 6061-T6 Aluminum OD= 3.625″ Installed Height= .875″ Hole size Needed= 3.375″ Fitting Threads= 1/2″ NPT Finish= Natural Machined Finish ** This sump must be welded in to an aluminum tank only**
$65.00
|
{ 0 comments }
|
Product # 27040 Material: 6061 Aluminum Cap: Vented: NO OD: 1.625″ ID: 1.25 Threads per inch: 14 Gasket: Buna-N O-Ring Included Neck: OD: 1.312″ ID: 1″ Length: 3″
$31.00
|
{ 0 comments }
| Gas Spring for toolbox lid. Approximate total length 9 inches.
Includes 2 mounting tabs.
$20.00
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
|
Product # 29009 Material: 6061 Aluminum Bolt Circle: 3.5″ CL x 6 places Hole opening: 2.500″ Threads: 8 Threads Per Inch Includes: Gasket, 8″ internal Lanyard, 6 SS Screws, Under Mounting Ring. -This Cap and neck assembly can be mounted to any type of tank material including Steel, Aluminum And Plastic.
$96.00
|
{ 0 comments }
|
Boyd Product # 37002 Gates Product # 27344 ID = 1/4″” EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
Regular Price:
Special Price: |
{ 0 comments }
|
Product Number: 11021 Tank Dimensions: 24 x 14 x 12 Fill Cap: Non Vented Threaded Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Pictures show product with sending unit installed. Sending Unit Purchased Seperate
$219.00
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
|
Boyd Product # 37014 Gates Product # 23964 ID= 1.5″ OD= 2″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$47.64
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37011 Gates Product # 23924 ID= 1.5″ OD= 2″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$67.14
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
This job was for a customers truck to be installed in the hauler body. Tank is 50 gallon built from 1/8th” diamond plate with a cargo rail.
{ Comments on this entry are closed }
Here’s a cool project we’re working on. Customer required a steel skid for the four tanks pictured below. Tanks feature our 1/2″ rollover safety vent.
{ Comments on this entry are closed }
Awaiting customer pickup is this custom aluminum tank for his VW Beetle. Notched for his steering column and featuring a custom sump. We utilized the customers supplied pump ring and our flush aircraft style fuel cap.
{ Comments on this entry are closed }
Here’s one getting ready to go out the door. This particular transfer tank was built to be mounted on top of the customers tool box in the bed of their truck.
Notched for the GPI fuel pump. This tank also included a 2″ aluminum cap & neck as well as a 1/2″ Rollover Safety Vent.
{ Comments on this entry are closed }
| Product Number: 13014
*Please Note: Our website does not reflect current stock levels.
$1,675.00
|
{ 0 comments }
| Product # 42003
The EZ-8 Pump is ideal for on-the-go fueling. This 12-volt DC fuel pump delivers 8 GPM, equivalent to standard gas stations. The system comes complete with power cord, manual unleaded nozzle, three-piece, trim-to-fit suction pipe and 10 ft of 5/8 in. hose.
$295.00
|
{ 0 comments }
| Product Number: 11016 500 Gallon 3/16 Aluminum tank Heavy Duty Steel Skid w/ Crane hooks 2 Internal Baffles Fully Welded Inside and Fully TIG Welded Outside -BUILT TO LAST Please Call For Freight Quotes: 352-447-2405
$4,625.00
|
{ 0 comments }
| Product Number: 37001 Sold in 1 FT Increments 25′ in a case Call for Case Pricing!
$3.75
|
{ 0 comments }
| Product Number: 13004 Pump Included *Please Note: Our website does not reflect current stock levels.
$765.00
|
{ 0 comments }
| Product Number: 13016
*Please Note: Our website does not reflect current stock levels.
$1,050.00
|
{ 0 comments }
| Product # 14014
Tank construction: .125 5052 aluminum *Please Note: Our website does not reflect current stock levels.
$750.00
|
{ 0 comments }
| Product # 14019
Direct Replacement Aluminum Tank Our website does not reflect current stock levels. Please allow 7 business days for fabrication and shipment. Are you a Dealer? if so We offer wholesale pricing and bulk discounts. Please call for more information
$575.00
|
{ 0 comments }
|
Product # 41004 Kit includes: *Our Brackets are not adjustable we fabricate each bracket based on your tank depth. Below you will need to choose the correct bracket length for your tank. The bracket length should be at minimum 1″ less than the depth of your tank. See below examples. EXAMPLE: 12″ deep Tank = 11″ Bracket length. Min/Max Bracket length = 6″ / 20″
$349.00
|
{ 0 comments }
| Product Number: 14008 Fits in stock location Does not hang down any further than stock tank Approx 20 gallons Aeromotive In-Tank Pump Included *Please Note: Our website does not reflect current stock levels.
$789.00
|
{ 0 comments }
|
Product Number: 14006 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$581.00
|
{ 0 comments }
|
Product Number: 14005 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$282.00
|
{ 0 comments }
|
Product Number: 14011 Will only replace ford part # (6C3Z9002F) Customer is responsible for confirming this. Boyd Welding will not pay for return shipping. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$638.00
|
{ 0 comments }
|
PRODUCT # 29001 This Package Saves 15% Off Individual Retail Prices Package Contents:
Regular Price:
Special Price: |
{ 0 comments }
|
Product Number: 14002 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 26.5 x 19 x 10 **Scroll down for FAQ on this product.
$349.00
|
{ 0 comments }
|
Product Number: 14001 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 26.5 x 19 x 10 **Scroll down for FAQ on this product.
$349.00
|
{ 0 comments }
|
Product Number: 14003 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Tank Dimensions: 26.5 x 19 x 10
$648.00
|
{ 0 comments }
|
Product Number: 14004 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Tank Dimensions: 26.5 x 19 x 10
$648.00
|
{ 0 comments }
| Product Number: 14017 Aeromotive In-Tank A-1000 Pump Approx 19 Gallons SUPPORTS 1200+ HP Shown With optional Rollover vent and Sending Unit. *Please Note: Our website does not reflect current stock levels.
$898.00
|
{ 0 comments }
| Product Number: 13008
*Please Note: Our website does not reflect current stock levels.
$750.00
|
{ 0 comments }
|
Product Number: 11005 Tank Dimensions: 10 x 10 x 16 Fill Cap: Flush Aircraft Style Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$159.00
|
{ 0 comments }
|
Product Number: 11004 Tank Dimensions: 12 x 12 x 8 Fill: 1.5″ OD Pipe * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$99.00
|
{ 0 comments }
|
Product Number: 13003 Tank Dimensions: 48 x 18 x 10 Fill Cap: 2″ NON Vented Threaded Cap P# 27017 * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$429.00
|
{ 0 comments }
| Product Number: 27030 3″ NON Vented Cap Key Locking Aluminum Neck Must Be Welded In
$75.00
|
{ 0 comments }
|
Product Number: 11014 Tank Dimensions: 24 x 18 x 12 Fill: 2″ Ribbed for Hose Pipe * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$249.00
|
{ 0 comments }
| Product Number: 13001
*Please Note: Our website does not reflect current stock levels.
$399.00
|
{ 0 comments }
| Product Number: 27018 Aluminum NON- Vented Cap Key Locking Aluminum Neck Must Be Welded in
$68.00
|
{ 0 comments }
|
Product Number: 11009 Tank Dimensions: 12 x 12 x 21 Fill Cap: Flush Aircraft Style Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$199.00
|
{ 0 comments }
|
Product Number: 11011 Tank Dimensions: 18 x 12 x 12 Fill Cap: Flush Aircraft Style Fill * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$179.00
|
{ 0 comments }
|
Product Number: 32001 Threads: 1/2″ NPT Hose Barb: 5/16″ Material: Brass Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position and also act as a Anti-Splash when your tank is full. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent
$31.00
|
{ 0 comments }
|
Product Number: 11002 Tank Dimensions: 8 x 6 x 6 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$89.00
|
{ 0 comments }
|
Product # 13017 • 185 Gallons Diesel Fuel
$4,500.00
|
{ 0 comments }
| Product Number: 14007 Fits in stock location Does not hang down any further than stock tank Approx 20 gallons *Please Note: Our website does not reflect current stock levels.
$490.00
|
{ 0 comments }
|
Product Number: 14030 Tank Dimensions: 46.5 x 6.5 x 10 Fill: 2″ OD Ribbed For Hose This product includes the Aeromotive Stealth 340 In-Tank Pump System.
* Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
Regular Price:
Special Price: |
{ 0 comments }
|
Product Number: 14013 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$789.00
|
{ 0 comments }
| 15 Gallon Replacement Tank Kelch Neck – Re-use your cap. Fits Model # 580.325601 *Please Note: Our website does not reflect current stock levels.
$199.00
|
{ 0 comments }
| Product Number: 14012 15 Gallons *Please Note: Our website does not reflect current stock levels.
$199.00
|
{ 0 comments }
| Welcome to the Build your own Transfer Tank Page. Picture shown is for fitting location reference only. Fill Cap, Fittings and mounting tabs are fixed locations and cannot be moved. Be sure to measure your vehicle before you order. Included items are 27017 NON vented cap, 32001 Rollover Safety Vent, QTY (3) 1/2″ NPT fittings and mounting tabs. This form is designed to provide instant pricing on a generic tank. If you need something custom We can do it just email us a completed drawing or sketch.
$316.00
|
{ 0 comments }
|
Product # 29002 This Package saves you 15% off retail pricing Package includes:
Regular Price:
Special Price: |
{ 0 comments }
| Product # 13012
Tank Dimensions: 52 x 26 x 16 *Please Note: Our website does not reflect current stock levels.
$975.00
|
{ 0 comments }
| Product # 14023
Tank Gallons = Approx 25 Includes:
$487.00
|
{ 0 comments }
|
Product Number: 14026 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 28 x 20 x 10 **Scroll down for FAQ on this product.
$369.00
|
{ 0 comments }
| Product Number: 13007 Fits most trucks with roll up bed cover *Please Note: Our website does not reflect current stock levels.
$575.00
|
{ 0 comments }
|
Product # 13020 Our website does not reflect current stock levels. Please allow 7 – 10 business days for fabrication and shipment. * Fits Below Bed Rails / Bed Covers * MAX Dimensions = 56.375″ L x 20″ W x 19″ H Tank Features: Toolbox Features: Scroll down for more details
$998.00
|
{ 0 comments }
|
Product Number: 11018 Tank Dimensions: 12 x 8 x 12 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$106.00
|
{ 0 comments }
|
Product Number: 11006 Tank Dimensions: 12 x 12 x 8 Fill Cap: NON-Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$109.00
|
{ 0 comments }
| Product # 13023
Each Fuel trailer is custom built per your requirements. Please call or email with your list of requirements and a quote can be provided.
$6,900.00
|
{ 0 comments }
|
Product Number: 13002 Tank Dimensions: 48 x 10 x 18 Fill Cap: 2″ Threaded NON Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$429.00
|
{ 0 comments }
|
Product Number: 11017 Tank Dimensions: 12 x 8 x 8 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$89.00
|
{ 0 comments }
|
Product Number: 11020 Tank Dimensions: 26 x 16 x 16 Fill Cap: Non Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$290.00
|
{ 0 comments }
| 25 Gallon Gasoline Tank 15 Gallon Mix fuel Tank Integrated Hose Wraps Product # 14016 *Please Note: Our website does not reflect current stock levels.
$2,150.00
|
{ 0 comments }
|
Product Number: 11019 Tank Dimensions: 24 x 12 x 18 Fill Cap: NON Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$249.00
|
{ 0 comments }
|
Product Number: 13018 Tank Dimensions: 40 x 10 x 18 Fill Cap: 2″ Full Function Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$347.00
|
{ 0 comments }
| Product Number: 27016 NON- Vented Cap Key Locking Aluminum Neck Must Be Welded in
$76.00
|
{ 0 comments }
|
Product Number: 11003 Tank Dimensions: 8 x 8 x 12 Fill Cap: Flush Mount Aircraft Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$129.00
|
{ 0 comments }
|
Product Number: 11012 Tank Dimensions: 30 x 12 x 12 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$259.00
|
{ 0 comments }
|
Product Number: 11010 Tank Dimensions: 18 x 12 x 12 Fill Cap: NON Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Alternate Pictures Shown With Optional 2″ Threaded Cap and Rollover Safety Vent
$159.00
|
{ 0 comments }
|
Product Number: 11001 Tank Dimensions: 8 x 6 x 4 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$79.00
|
{ 0 comments }
I just received my tank and all I can say is Wow!
I am a bit of a perfectionist and generally hard to please, but you guys blew me away. Working with you exceeded my expectations. Not only is your customer communication great and you beat my expectations on fabrication time and delivery, but the product you produce is top notch.
The finished tank matches the drawing perfectly and the quality of manufacture and materials is world class. I was worried about doing this transaction over the internet from a drawing since in past I used local people, but I have to say yours is the best tank I have had done so far. In past I was used to getting a tank with chips in it or scratches all over it, bit not yours, perfectly cut, finished, and clean – Nice work!
I will recommend you to everyone I know
Regards
Alex
{ Comments on this entry are closed }
{ Comments on this entry are closed }
This Page is Currently Under Construction. In the mean time if you have questions don’t hesitate to ask.
{ Comments on this entry are closed }
Q: Do you build custom tanks?
A: Yes, Every tank that we build is custom made to your requested dimensions and shape. However, below is a list of tanks we do not build.
-We do not build Steel or Stainless Steel Tanks of any type. We strictly specialize in the fabrication of aluminum tanks.
-We do not build Round, Oval or D-Style Tanks.
-We do not build Aircraft fuel tanks of any kind (Experimental or Not).
-We do not build Primary or “tear drop” style motorcycle tanks.
-We do not build Pressure Vessels or vaccum tanks.
-We do not build potable water tanks
-We do not build tanks for LP or CNG.
Q: I would like to have a custom tank built, How do i calculate gallons?
A: The basic formula for finding gallons of a rectangle is L x W x H / 231 (Length x Width x Height divided by 231) once you have that number you should deduct 10% and that is what would be called “usable gallons” you should always figure your tank size at usable gallons.
Q: How Long will it take to build my tank?
A: Under most circumstances our production times are 7-10 business days for fabrication. Complex projects may take longer.
Q: Is a custom tank expensive?
A: Depends, the word “Custom” does not always mean thousands of dollars. Your price will depend on a few different factors like size and complexity. Gallons of the tank do not play a huge role in the price since there are many different configurations to get a specified amount. I think that you will find that our prices are reasonable for the quality we produce and flexible services we provide. I would suggest spending a few minutes preparing a clear sketch or drawing of the tank you would like to have built upload it using the “Request Quote” form.
Q: What is the best way to get my drawing to you for a quote?
A: You can Email your drawings to us. you can find our email addresses in the Contact Us page of our site.
Q: Do you have a tank for my 19** (Make, Model)?
A: We do not build tanks for specific makes or models, we strictly only build custom tanks to supplied drawings.
Q: I don’t have a drawing, can I send you my old tank?
A: We do not build tanks using old tanks as a substitute for a drawing. Unless we have requested that you send your old tank for reference please don’t ship it to us.
Q: We are a business and would like you to produce a tank for us in volume can you do it?
A: Yes, We produce tanks ranging in sizes for many OEM and aftermarket companies. Shoot us an email or give us a call to discuss your particular needs.
Q: Do you repair used tanks?
A:No, We do not do any type of repair work.
Q: Do you offer installations
A: No, we do not offer installations
Q: Can I modify a standard tank to better suit my needs
A: Yes, Since we manufacture our tanks in-house any tank can be modified. Pricing and lead times will depend on order volume and frequency. A clear detailed sketch showing the modifications will be required.
{ Comments on this entry are closed }
Part# 32005
-8 An Rollover Safety Vent
-Must Be Welded in
- Aluminum
{ Comments on this entry are closed }
Tank dimensions = 40 x 9.5 x 10
Tank Material = .125 Mill aluminum
(1) 2″ ribbed pipe for filler
(1) Sending Unit Flange
(4) 1.5 x 2″ mounting tabs
(2) Baffles
(1) 1/2 npt fitting for Roll Over Vent
(1) Aeromotive A1000 In-tank Pump
Fits without any modification to your chassis or body panels
{ Comments on this entry are closed }
Tank dimensions = 40 x 9.5 x 10
Tank Material = .125 Mill aluminum
(1) 2″ ribbed pipe for filler
(1) Sending Unit Flange
(4) 1.5 x 2″ mounting tabs
(2) Baffles
(1) 1/2 npt fitting for Roll Over Vent
(1) Aeromotive Stealth 340 IN-Tank EFI pump
Fits without any modification to your chassis or body panels
{ Comments on this entry are closed }
The tank looks great and fits perfect. I have attached a couple of photos of the tank installed in the chassis. Hopefully in the next few weeks I’ll be able to send some of the finished chassis, painted a dark blue, which should really make the aluminum tank stand out.
Thanks again for all the help and for providing a great looking product.
Walter S. Green
2g Performance, LLC
{ Comments on this entry are closed }
Dan: Just want to thank you guys for the gas tank you built for me. It is accurate to my drawing in every detail, and beautifully crafted. You guys are the best!
‘ Till next time, Regards.
Bob
{ Comments on this entry are closed }
I have installed the new fuel tank on my motorhome. The workmanship and fitup were excellent. I will recomend your company to anyone needing a replacement fuel tank for a motor home. Once again THANK YOU for the excellent job on my fuel tank.
Bob Carlson, Rozet Wyoming
{ Comments on this entry are closed }
Several weeks ago I searched the internet to find someone to build me a custom aluminum one gallon header tank for my experimental aircraft. I came across Boyd Welding website and saw the custom tanks that this company manufactures and decided to give them a call to see if they could fabricate this small header tank. I had the pleasure of speaking with a gentleman, Dan Hance, about building this header tank and he was interested in building this tank if I could send him some drawings. I sent him some drawings and pictures of a plastic header tank that I wanted copied and Dan sent me back within a day, the quote for the cost of this header tank. The price for the header tank I felt was very reasonable so I asked Dan to build this tank. After I sent him the drawings I realized I had a couple of changes dimensional wise so I called Dan and he kindly made the changes to my request and one week later I had my new header tank. I could not be more pleased with how it was fabricated and how nice it was to work with Dan Hance. If someone needs a custom fuel tank or cell made, Boyd Welding is your answer. Their pricing is reasonable and their workmanship is first class plus the customer service is the kind of service we are all looking for.
{ Comments on this entry are closed }
Extra large capacity tank fits the Coleman 5000 generators
Tank dimensions: 26 x 15.5 x 12
Gallons = 15 gallons
Material: .125 mill aluminum
Kelch neck (use existing cap)
1/4″ NPT draw fitting in bottom
This is a must have for camping, racing, off-roading or long term power outages. No need to carry gas cans again. Meets all EPA CARB requirements.
{ Comments on this entry are closed }
The fuel tank has arrived and it looks great!
I fitted it in and it seems to fit perfectly. Amazing, I was able to send you guys a simple drawing, and you fabricated the tank perfect from the other side of the continent. And then shipped it up to me all for significantly less money than any of the local shops could do it.
A big thank you from Alaska!
Reuben
{ Comments on this entry are closed }
Boyd Welding 2″ NPT Threaded Aluminum Cap
Machined Finish
NON Vented
6″ Chain and Crossbar
Aluminum Fill Neck must be welded on
overall length roughly 3″
{ Comments on this entry are closed }
Tank dimensions = 30 x 26.5 x 15
Tank Material = .125 Mill aluminum
35 Gallons
(1) 1.5″ ribbed pipe for filler
(1)7/8″ Ribbed Vent fitting
Provisions to use the stock pump
Includes mounting Straps
includes rollover Safety vent
Fits in all 06 F-350 rear skid plates.
Click Below for more pics
{ Comments on this entry are closed }
Custom aluminum auxiliary tank for the Hummer H1
Gallons: 110
Material: 3/16 5052 Aluminum
Dimensions: 42.5 x 49.5 x 13
-Wisco Flush Filler Cap
- Roll over Safety Vent
-3/8 NPT pickup tube
-4 Heavy Duty Lifting Lugs
- Cross Structure Baffles
This tank is built tough to take the beatings of Hard Core off-Roading and to Give you peace of mind knowing you have enough fuel on board to get you home.
Click See More Below for more pictures
Shop Online
{ Comments on this entry are closed }
Dave and Dan,
Thanks for a nice tank. Got the tank installed, looks good and seems to work good so far.
Would have been a little easier to install if I had specified 61″ instead of 62″ long, mainly for plumbing.
Thanks to Dan for the patience and help in working with me on the design and details.
A few pictures attached.
Thanks again,
Jim Rogers
{ Comments on this entry are closed }
Boyd Welding Crew,
Just wanted to let you guys know we received the tank and it is awesome. You did a wonderful job and we are very pleased with it.
Thank you so much
Mark/Christy Silva
{ Comments on this entry are closed }
Dave / Dan
The gas tank you just made for me fits perfect and turned out awesome.
Thanks again,
Brett Ward
{ Comments on this entry are closed }
Dave-
I wanted to let you know that the tank you built for us is working out great.
I will try to get some good pictures of our application for you.
Thanks again,
Geoff
{ Comments on this entry are closed }
5-18-11
Hello Dave and Dan……Just wanted to drop you guys a note and thank you for the help and interaction to make the new gas tank for my 30 Model A……….tank worked out perfectly and looks great!!!……attached a couple of shots of the tank and the car it resides in.
Thanks again, Bill (New York)
{ Comments on this entry are closed }
5-16-11
Hey Dan,
I just wanted to take a minute and let you know that I GREATLY appreciate the time you took to work with me on the RZR tank. The fit is perfect, and it looks great. Your prices are right, your service is awsome, and the craftsman ship is top notch.
I appreciate you and your company.
Thank you very much,
Justin R.
{ Comments on this entry are closed }
5-19-11
Dave and Dan,
Thanks for the great service. From concept to design, fabrication and installation. I would recommend anyone looking for a tank to get with these guys. It has been a pleasure doing business with your Company.
Sincerely
Ron C
{ Comments on this entry are closed }
Aluminum Kelch style neck
Fits most Lawnmower or golf cart plastic caps
{ Comments on this entry are closed }
2″ Rubber Filler Pipe hose
Flexible without kinking
Can be bent almost any angle.
Best fuel filler hose you can buy!
Sold per/ft
Select how many feet you need by adding or subtracting QTY in Checkout
{ Comments on this entry are closed }
2″ Rubber Filler Pipe hose
NOT Flexable without kinking
Best used in Straight Fitment applications
Sold per/ft
Select how many feet you need by adding or subtracting QTY in Checkout
{ Comments on this entry are closed }
5/16 Fuel Hose For EFI Applications
Sold Per/ft
Select how long you need by adding or subtracting QTY in Checkout
{ Comments on this entry are closed }
5/16 NON EFI Fuel Hose
Sold Per/ft
Select how long you need by adding or subtracting QTY in Checkout
{ Comments on this entry are closed }
Part# CN021
Non Vented Aluminum 4″ fuel cap
Threads onto 4″ male NPT
12″ chain and cross bar
Aluminum Neck must be welded to Tank
overall height roughly 3.5″
{ Comments on this entry are closed }
Part# CN020
Cast aluminum
Threads onto a 2″ male NPT
Vented
Pad lockable
Perfect for Stationary Bulk Tanks
{ Comments on this entry are closed }
2″ NPT Threaded Aluminum Cap
NON Vented
6″ Chain and Crossbar
Aluminum Fill Neck must be welded on
overall length roughly 3″
{ Comments on this entry are closed }
2″ Mushroom Vent
Threads onto a 2″ NPT Male Fitting
Best used in Stationary Bulk Containers
Screen to keep Bugs out
{ Comments on this entry are closed }
Part# CN018
Threads into 1/2 NPT female fitting
5/16 hose barb
Machined From Brass
1″ installed height
No Thermal Relief
This part is required by D.O.T on all Transfer or Aux Fuel tanks.
{ Comments on this entry are closed }
Mechanical Gauge
Fits 5 bolt Flanges
Choose Tank Depth Below
Sender should be at-least 1″ shorter than Inside tank depth
{ Comments on this entry are closed }
2″ Fuel Gauge
240-33 Ohm
Universal application
Dont forget the matching Tank Level Sender!
{ Comments on this entry are closed }
In-Line fuel filter for Gasoline applications
Use with 5/16 or 3/8 fuel lines (choose below)
{ Comments on this entry are closed }
Inline 12V Rotary Vane Pump
Used For gasoline or diesel applications
70 GPH
Perfect for transferring Gasoline or diesel from your AUX tank to your Primary tank.
{ Comments on this entry are closed }
Tank dimensions = 30 x 26.5 x 15
Tank Material = .125 Mill aluminum
35 Gallons
(1)1.5″ ribbed pipe for filler
(1)7/8″ Ribbed Vent fitting
Includes Mouting Straps
Includes rollover safety Vent
Provisions to use the stock pump
Fits in all 06 F-550 rear skid plates.
Click Below for more pics
{ Comments on this entry are closed }
Tank dimensions = 36 x 16 x 11
Tank Material = .125 Mill aluminum
(1) 2″ ribbed pipe for filler
(1) Sending Unit Flange
(3) Baffles
(1) 3/8 Pickup tube
(1) 3/8 Return
Fits without any modification to your chassis or body panels
Click more for more pictures
{ Comments on this entry are closed }
 |
2811 NW 8th Pl
Ocala, Fl 34475 Phone (352) 447-2405 Fax (352) 447-2403 |
Press Release
| Contact: Dave Boyd
Phone: (352)447-2405 |
FOR IMMEDIATE RELEASE
9 A.M February 16, 2011 |
Boyd welding Introduces Factory Five 33 Hot Rod Replacement Fuel tank.
Ocala, fl February 16 2011: Boyd Welding Manufacturer of custom aluminum fuel tanks introduces the replacement tank for all Factory Five 33 Hot Rod DIY Kits (Part# FF33). This 1/8″ thick aluminum tank replaces the supplied steel tank and installs without any modifications to the existing chassis or body panels. The FF33 Is cut and formed on in-house CNC Plasma and CNC Press Brakes. All parts are T.I.G welded together and pressure tested to ensure the highest quality then packaged with care.
Options available:
- Non EFI with Pickup tube for carburetor applications. (standard)
- EFI In-Tank Pumping System using Walbro high pressure pumps for fuel injection applications.(optional)
- 0-90 ohm or 240-33 ohm sending units available with matching gauges (optional)
- Thread-in Roll Over Safety Vent (optional)
- Machined Filler neck with Rib secure hose (standard)
Each tank can be customized to fit specific applications. All aluminum gasoline, diesel or jet fuel tanks carry a 2 year warranty. For more information visit Boyd Welding’s website at www.boydwelding.com or call M-F 9-5:30 EST.
{ Comments on this entry are closed }
Wisco Cap Install
11 Gallon Demo
67-72 Chevy Tank Demo
Wastegate Flange
{ Comments on this entry are closed }
Tank dimensions = 40 x 9.5 x 10
Tank Material = .125 Mill aluminum
(1) 2″ ribbed pipe for filler
(1) Sending Unit Flange
(4) 1.5 x 2″ mounting tabs
(2) Baffles
(1) 1/2 npt fitting for Roll Over Vent
Fits without any modification to your chassis or body panels
{ Comments on this entry are closed }
Tank dimensions = 8 x 8 x 12
Tank Material = .125 Mill aluminum
(1) Wisco Aircraft Style Cap
(4) 1/2 NPT Fittings
(2) 1 x 1 mounting tabs
Bottom Tapered for Fuel Flow To Fittings.
Mounting tabs can be modified to suit Particular needs.
Great for Engine Run Stands.
{ Comments on this entry are closed }
Tank Dimensions: 8 x 6 x 4
Tank Material: .125 aluminum
(1) Standard Vented Twist Cap
(2)-8 An Male
(2) 1 x 1 Aluminum Mounting Tab
Mount To Firewall or inner fender for coolant Reservoir or Stand alone Nitrous Tank. Can Be used for Go Carts or Lawnmowers.
{ Comments on this entry are closed }
-Brass 90 degree NPT
-Will not corrode threads
{ Comments on this entry are closed }
- .125 Mill Aluminum
- Aluminum Hinge and Rivets Will Not Rust
- Self Ejecting Butterfly Dzus Fastner
{ Comments on this entry are closed }
Mounts Behind Rear Axle
Tank Dimensions: 26.5 x 19 x 10 deepest
Tank Material: .125 aluminum
(1) In-Tank EFI System With Aeromotive Stealth 340
(1) Twist Cap 3″ tall
(1) .375 FTP vent
(1) .375 FPT (Fuel) opposite corner bottom
(1) sending unit flange
(4) 3 x 3 aluminum mounting tabs
{ Comments on this entry are closed }
Paul from Nationwidefoamadhesive.com contracted us on 10/4/10 to build a custom tank for the side of his Isuzu NPR box truck. He requested the tank hold approx 35 gallons and built from .125 mill aluminum. We used our existing 25 gallon design and extended it to match his cross members and meet his gallon requirements. This aluminum tank is fully baffled to control fuel movement and will work for both gasoline or diesel fuel. We also added a mechanical fuel level gauge , safety vent and Non-Vented Velvac cap. Here is a link to the 25 gallon Tank we offer. If you live in Florida or plan to build a home be sure to contact Paul at 1-(866)-590-3626 for your insulation needs. If you need a tank give us a call Toll Free 877-270-3576. Click More info below to see pictures.
{ 0 comments }
Tank Dimensions: 48 x 60 x 48
Tank Material: .188 Mill Aluminum
(1)Velvac Cap
(1) 2″ Mushroom Vent
(1) 2″ NPT Pump Fitting
(1) 2″ SS Fuel Gauge
(2) Baffles
Fully welded all aluminum trailer
(2) 3500 lb axles
(4) 15″ tires and rims
Heavy Duty Pintle hook hitch
Swing away jack
Picture shows optional standing platform and steps.
{ 0 comments }
* Standard nozzle hanger
* Comes with 10 feet of hose
* Direct tank mount
* UL listed motor
* Two-piece suction pipe
{ 0 comments }
-Standard connection used for most marine and truck application.
-Will not corrode threads
Shop Online
More Info…
{ 0 comments }
Adjustable depth of 5-26″
Standard 5 bolt flange
O-Ring 10-32 machine screws
Includes Gasket
{ 0 comments }
Required in most racing applications
Block Dimensions = 16 x 6 x 3
Sold individually
Does not allow Fuel slosh and prevents fuel starvation.
Tube Style sending unit required.
Most tanks require multiple blocks
Must be replaced every 5 years
Call to Order!
{ 0 comments }
Allows air in but does not allow fuel out.
Part# CN009
Threads into 1/2 Npt female fitting
5/16 hose barb
Installed height is 1″ or less
Required for all Transfer tanks, Aux tanks, Race Tanks
Thermal Relief
{ 0 comments }
Comes in Small or Medium Sizes
.125 5052 Aluminum
Select your fitting sizes!
Must be welded in tank
{ 0 comments }
Block off sending unit flange
Can be used on any tank
Gasket and Machine screws included
{ 0 comments }
U.S Standard 5 bolt flange
Aluminum heat treated
10-32 machine screw threads
Will fit most sending units
Must be welded in tank
{ 0 comments }
3/8 or 1/2 NPT fitting with pickup tube welded to the back
Standard length is 12″ / 18″ / 24″ (cut to fit yourself)
call to request custom length
MUST BE WELDED INTO EXISTING TANK
{ 0 comments }
-fittings used on all of our tanks
-Aluminum, Steel, Stainless Steel
-NPT Threads
Many Sizes Availible
BUY IN BULK (50+) SAVE $$
{ 0 comments }
Flush Racecar Filler (positive locking)
6 Bolt Mounting
Comes With Gasket and Mounting Hardware
Perfect if you have tight space requirements
{ 0 comments }
Brass non-vented thermal relief Cap
2″ male threaded neck
Must Be Welded in!
Perfect for Transfer Tanks
{ 0 comments }
Aluminum Weld-In Neck
Approx 1.5″ in height
Vented or Non-Vented
Great cap for many universal applications.
See Videos Page for demonstration!
{ 0 comments }
Mounts Behind Rear Axle
Tank Dimensions: 26.5 x 19 x 10 deepest
Tank Material: .125 aluminum
(1) Twist Cap 3″ tall
(1) .375 FTP vent
(1) .375 FPT (Fuel) opposite corner bottom
(1) sending unit flange
(4) 3 x 3 aluminum mounting tabs
{ 0 comments }
Tank Dimensions = 24 x 22.5 x 12
(1) Brass Non Vented Cap
(1) Mechanical Fuel Level Gauge
(1) Safety Vent
(1) 3/8 Pickup Tube
(1) 3/8 Return
(2) Baffles
{ 0 comments }
Tank Dimensions (overall) 72 x 42 x 6 Cabside is 18T x 4w
Tank Material: .188 Diamond & Smooth Aluminum
(1) Brass non-vent (Velvac) fill cap
(1) 2″ NPT for transfer pump (optional)
(1) .5 NPT vent
(2) .5 NPT for drain and gravity feed
Fully Baffled
Maximum Weight Cap (2000lbs)
Picture Shown Is Actual Tank
{ 0 comments }
Tank Dimensions:48 x 24 x 18
Brass non-vented Cap
(2) .5 NPT at bottom for Gravity feed
(1) .5 NPT Vent
(2) baffles
(4) mounting tabs
Notch dimensions: 14 x 12 x 10
{ 0 comments }
Tank Dimensions: 47 x 20 x 16
Tank Material: .125 mill aluminum
Brass non-vented Cap
(2) .5 NPT at bottom for Gravity feed
(1) .5 NPT Vent
(2) baffles
(4) mounting tabs
(1) Sending Unit Flange
(1) 2″ fitting for transfer pump
Notch dimensions 14 x 10 x 10
Use GPI Pump for best fit
{ 0 comments }
Tank Dimensions: 24 x 18 x 12
Tank Material: .125 aluminum
(1) 2″ Ribbed for Hose Filler
(1) 3/8 NPT vent
(2)1/2 NPT Fittings on bottom end for draw
(1) 3/8 NPT return or extra fitting
(4) 1.5 x 1.5 aluminum mounting tabs
(1) Sending unit flange
{ 0 comments }
Tank Dimensions: 30 x 12 x 12
Tank Material: .125 aluminum
(1) Standard Vented Twist Cap
(1) 3/8 NPT Pickup Tube
(1)3/8 NPT Fitting on bottom end for drain
(1) Standard Sending Unit Flange
(4) 1.5 x 1.5 aluminum mounting tabs
{ 0 comments }
Tank Dimensions: 12 x 12 x 21
Tank Material: .125 aluminum
(1) Wisco Flush Aircraft Filler
(1)1/2 NPT vent
(2) 1/2 NPT Fittings on bottom sump for Draw
(1) 1/2 NPT return or extra fitting
(4) 1.5 x 1.5 aluminum mounting tabs
(1) Fuel Sump
{ 0 comments }
Tank Dimensions: 18 x 12 x 12
Tank Material: .125 aluminum
(1) Wisco Flush Aircraft Filler
(1) 1/2 NPT vent
(1) 1/2 NPT W/Pick up tube
(1) 1/2 NPT return or extra fitting
(1) Sending unit flange
(4) 1.5 x 1.5 aluminum mounting tabs
{ 0 comments }
Tank Dimensions: 18 x 12 x 12
Tank Material: 14GA mild steel
(1) Standard Twist Cap
(1).375 NPT vent
(1).375 NPT W/Pick up tube
(1).375 NPT return or extra fitting
(1) Sending unit flange
(4) 1.5 x 1.5 Steel mounting tabs
Picture shown is actual tank.
Please Call For Availability and Pricing!
More Info…
{ 0 comments }
Tank Dimensions: 48 X 39 X 9
Tank Material: .125 aluminum
(1)1.5″ Ribbed for hose filler
(1).375 od vent tube ribbed
(1).375 FPT W/Pick up tube
(2) Baffles
(1) Sending Unit Flange
(1) Ground Tab
{ 0 comments }
Tank Dimensions: 40 X 22 X 6.5
Tank Material: .125 aluminum
(1)1.5″ Ribbed for hose filler
(1).375 od vent tube ribbed
(1).375 FPT W/Pick up tube
(2) Baffles
(1) Sending Unit Flange
(1) Ground Tab
{ 0 comments }
Tank Dimensions: 18 x 12 x 12
Tank Material: .125 aluminum
(1) Standard Twist Cap
(1).375 FPT vent
(1).375 FPT W/Pick up tube
(1).375 FPT return or extra fitting
(1) Sending unit flange
(4) 1.5 x 1.5 aluminum mounting tabs
Picture shown is actual tank.
{ 0 comments }
Tank Material: .125 Mill Aluminum
Tank Dimensions 48 x 24 x 17 – (19″ W/Cap)
(1) Velvac Non-Vented Cap
(1) 2″ Npt for transfer pump
(3) 1/2 NPT fittings for Gravity Feed, Drain and Vent
(4) Mounting Tabs
(2)Baffles
CALL TO ORDER THIS TANK.
Shop Online
{ 0 comments }
Tank Dimensions:
48 x 22 x 16 Step= 8T x 11D
Will fit most full size trucks with roll up cover
Brass non-vented (Velvac) Cap
(2) .5 NPT at bottom for Gravity feed
(1) .5 NPT Vent
(2) baffles
(4) mounting tabs
Shown with optional Either side Fill
{ 0 comments }
Tank Dimensions: 48L x 10W x 18T
Tank Material: .125 aluminum
(1)Standard Twist Cap & Neck
(1) .375 FTP vent
(1) .375 FPT W/Pick up tube
(1) sending unit flange
(4) 1.5 x 1.5 aluminum mounting tabs
(2) Baffles
{ 0 comments }
Tank Dimensions: 50 x 12 x 16
Tank Material: .125 aluminum
(1)Standard Twist Cap & Neck *vented
(1) 2″ fitting for transfer pump
(1) 1/2 NPT for drain
(1) 1/2 NPT for gravity feed
(1) sending unit flange
(2) 1.5 x 1.5 x 6 aluminum mounting tabs
(2) Baffles
Maximum overall height = 18″ with cap
Shop Online
More Info…
{ 0 comments }
Tank Dimensions: 48 x 18 x 10
Tank Material: .125 aluminum
(1)Standard Twist Cap & Neck
(1) .375 FTP vent
(1) .375 FPT W/Pick up tube
(1) .375 FPT return or extra fitting
(1) sending unit flange
(4) 1.5 x 1.5 aluminum mounting tabs
(2) Baffles
Shop Online
{ 0 comments }
Tank Dimensions: 48 x 10 x 18
Tank Material: .125 aluminum
(1) GPI 15 GPH Pump
(1)Standard Twist Cap & Neck
(1) .5 Vent
(1) 2″ NPT Pump Fitting
(2) 1.5 x 2 x 6 aluminum mounting tabs
(2) Baffles
{ 0 comments }
Tank Dimensions: 48 x 7 x 17
Tank Material: .125 aluminum
(1)Standard Twist Cap & Neck
(1) .5 Vent
(1) 2″ NPT Pump Fitting
(1) sending unit flange
(2) 1.5 x 2 x 6 aluminum mounting tabs
(2) Baffles
Shop Online
{ 0 comments }
Tank Dimensions: 10 x 10 x 16 deepest
Tank Material: .125 aluminum
(1) Flush aircraft style cap
(2) .375 NPT vent & return
(2) .375 NPT feed at bottom in sump
(1) sump facing rear
(4) 1.5 x 8″ mounting tabs
(Mounting tabs can be placed anywhere in any configuration)
(Can be ordered with 1/2″ NPT fittings)
{ 0 comments }
Tank Dimensions: 12 x 12 x 8
Tank Material: .125 aluminum
(1)1.5″ Ribbed for hose filler
(1).375 od vent tube ribbed
(1).375 FPT W/Pick up tube
(1).375 FPT return or extra fitting
(4) 1.5 x 1.5 aluminum mounting tabs
Picture shown is actual tank without mounting tabs.
{ 0 comments }
This Website is best viewed using Mozilla Firefox or Google Chrome Browsers
-Dave
More Info…
{ 0 comments }
WELCOME TO THE NEW BOYD WELDING WEBSITE!
Thanks for visiting our new site. We know it’s been a long time coming and appreciate everyone’s patience. We hope you find it was worth the wait.
Not only do we finally have our full product line available for browsing, but we’ve got some pretty neat interactive features, too.
We’ll be using this News section to let everyone know about stuff we’re working on and to post general announcements about the site and our products.
Please take a look around and visit us again soon. Thanks to all of our customers for allowing us to keep doing what we love – providing people with the best fuel tanks we can!
More Info…
{ 0 comments }
