| Boyd Welding 2″ Machined Cap & Neck
$49.00
|
{ 0 comments }
From the category archives:
BRASS FITTINGS
|
Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck with cap is approx 3″ tall. Q: Will the fill cap stick through my bed floor?A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank. Q: What do i get if i choose the Flush Floor Fill? A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill. Q: Are there Baffles in the Tank? A: Yes, There are 3 baffles in the tank. Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$686.00
|
{ 0 comments }
|
Frequently Asked Questions:Q: How Far down are the mounting tabs? A: 3″ down from the top of the tank Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall. Q: Will the fill cap stick through my bed floor? A: No, when the tank is mounted to the bottom of the frame rails as intended the fill cap will be right below the bed floor. you will need to purchase or fabricate an access door big enough for your hand to reach through and remove the cap to fill the tank. Q: What do i get if i choose the Flush Floor Fill? A: If you choose the Flush Floor Fill when purchasing the tank then we will automatically remove the threaded cap and neck and replace it with a 2″ Ribbed Barb that sticks up roughly 1.25″ to connect directly to the Flush Floor Fill. Q: Are there Baffles in the Tank?A: Yes, There are 3 baffles in the tank. Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen. $369.00
|
{ 0 comments }
|
Frequently Asked Questions:Q: How Far down are the mounting tabs? A: 3″ down from the top of the tank Q: How Tall is the fill neck? What is the Diameter of the pipe? A: The fill neck is approx 3″ tall. The pipe is 2″ OD Q: Are there Baffles in the Tank? A: Yes, There are 3 baffles in the tank.Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffeling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. Q: Will this tank fit my 63-66? A: Yes, the 63-66 utilizes the same framerails. Many customers have sucessfully used this tank for those year ranges. Q: I have a Blazer, can i use this tank? A: Many customers have sucessfully installed the side fill tank into their blazers however, i am unsure of the scope of work to make it happen.
$369.00
|
{ 0 comments }
| Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. $686.00
|
{ 0 comments }
| Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3.5″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. $686.00
|
{ 0 comments }
| Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. $951.00
|
{ 0 comments }
| Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. $369.00
|
{ 0 comments }
| Frequently Asked Questions:
Q: How Far down are the mounting tabs? Q: How Tall is the fill neck? A: The fill neck is approx 3″ tall.
Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent option. Q: I Currently have a carbureted engine but may want to go EFI in the future. Can i upgrade this tank to EFI? A: Yes, We have designed our tank with the EFI provision and baffling to allow you to upgrade to EFI using our Aeromotive in-tank pump system. All you will need to purchase is the pump system, remove the cover plate and bolt in the pump system using the same hardware. $369.00
|
{ 0 comments }
| Dimensions = 23 x 20.5 x 17.190 Material = .190 5052 mill aluminum 2″ OD Fill pipe 1/2″ NPT Vent Fits in the stock location using all stock pump and components
$575.00
|
{ 0 comments }
| Dimensions = 26.125″L x 20.125″w x 17.375″T Material = .190 5052 mill aluminum 2″ OD Fill pipe 1/2″ NPT Vent Fits in the stock location using all stock pump and components
$675.00
|
{ 0 comments }
|
PRODUCT # 25018-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-18) Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$67.93
|
{ 0 comments }
| PRODUCT # 25018-12
MATERIAL: Stainless Steel
OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank)
ID Thread = 3/8 NPT Female
Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-12)
Minimum Tank Depth = 2″
Maximum Tank Depth = 12″
Screen= NO
Overall Installed Height = 3/8″
***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$59.06
As low as: $32.48 |
{ 0 comments }
|
PRODUCT # 25018-06 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .437″ ID (Need a Smaller tube? See SKU# 25016-06) Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$50.19
|
{ 0 comments }
|
PRODUCT # 25016-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$51.06
|
{ 0 comments }
|
PRODUCT # 25016-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$55.93
|
{ 0 comments }
|
PRODUCT # 25016-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$60.80
|
{ 0 comments }
|
PRODUCT # 25016-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$65.67
|
{ 0 comments }
|
PRODUCT # 25016-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$70.54
|
{ 0 comments }
|
PRODUCT # 25016-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .305 -.312 +/- (Need a Bigger tube? See SKU# 25018-06) Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$46.19
|
{ 0 comments }
|
Product # 44033
Material: 5052 Aluminum
OD: 6″
ID: 4.375″
Bolt CL : 5.25″
Installed Height: .250 +/-
Threads: 10-32 Zinc Plated Threadsert
Harware Included: YES
Gasket: YES
Cover Plate Thickness: .125″ (1/8″)
Bolt in Assembly, No Welding needed.
Will work with any type of tank, Aluminum, Plastic, Steel or Stainless
This product is for use on the top of tank only.
$38.57
|
{ 0 comments }
|
Product Number: 14044 WILL FIT YEARS 60-62 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: This product is in-stock but may take up to 5 days for shipment. -Tank Dimensions: 35.5 x 19 x 10 **Scroll down for FAQ on this product.
$399.00
|
{ 0 comments }
|
Product Number: 14046 WILL FIT YEARS 60-62 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: This product is in-stock but may take up to 5 days for shipment. -Tank Dimensions: 35.5 x 19 x 10 **Scroll down for FAQ on this product.
$699.00
|
{ 0 comments }
|
Product # 46002
Replacement Boyd Welding Tank Cleanout Gasket 8 Bolt
Material: BUNA- N
Thickness: .125″
OD: 6″
ID: 4.375″
x8 .250 holes on 5.25″ BCL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$9.25
|
{ 0 comments }
|
SKU# WBRKT-300
- ALUMINUM CONSTRUCTION
- CHAIN INCLUDED
- SINGLE BOTTLE
- HOOK HOLES FOR WRENCH
Dimensions:
14.5″ Long
6″ Wide ( sticks out from wall)
Bottle Diameter = 9.25″ (Standard 300CF welding bottle)
Mounts to any type of wall. Mounting hardware NOT included.
$36.00
|
{ 0 comments }
|
Product #27042
Cap: Neck: -Bolt- IN - Hole Cut Size = 3.760″ MIN / 3.950″ MAX (3-3/4″ hole saw) - Bolt hole Center = 4.350″ Kit Includes: - 1) CNC Machined CAP W/ Oring and Delrin Key - 1) CNC Machined flush bed fill neck 2″ RFH - 1) 4″ Long 2″ID Fuel Fill Hose - 2) Stainless worm clamps ( Optional components based on selection below) ****Hardware to mount to your bed floor not included***** FAQ: Q: What size hose does this use? A: The ribbed part of this neck is 2″ so you will need to purchase 2″ ID Fuel fill hose. We sell this in 3′ lengths SKU# 37015 Q:I already purchased a bed fill C-10 tank with a Boyd cap, will this work with what I already have? A: Yes, you will need to select “Yes” below so we can provide extra parts in this kit to adapt the Flush Bed fill to the threaded neck. The procedure to make this work is outlined in the instructions provided.
$99.75
|
{ 0 comments }
|
Product # 44032
Material = CNC Machined 6061-T6 OD= 6.00″ ID= 3.510″ Height = 0.500″ Installed height without pump = 0.625″ Bolt Circle A (BW EFI) = x12 @ 5.00″ BCL Bolt Circle B (Aeromotive) = x10 10-32 @ 4.00″ BCL This CNC machined aluminum adater will allow you to adapt any Aeromotive phantom, A1000 or Eliminator in tank pump that utilizes the 10 bolt pattern to the Boyd Welding 12 bolt pattern. Kit Includes: 1) CNC Machined Adapter Plate 1) BW EFI Buna Gasket 12) 10-32 1″ Stanless Screws (BW Pattern) 10) 10-32 3/4″ Stainlss Screws ( Aeromotive Pattern) You will use the gasket and nylon washers that was supplied with the aeromotive pump you purchased. do not try to use the screws supplied with Aeromotive pumps.
$58.00
|
{ 0 comments }
|
Product #27041
Cap: Neck: -Bolt- IN - Overall Installed Height W/ Cap = .210″ - Hole Cut Size = 3.760″ MIN / 3.950″ MAX - Bolt hole Center = 4.350″ Kit Includes: - 1 CAP W/ Oring and Delrin Key - 1 Bolt In Neck - 1 Buna Gasket - 1 Under Ring W/10-32 thread serts - 8 SS 10-32 Flat Head Machine Screw
$89.75
|
{ 0 comments }
|
Product # 21030
This Item is sold individually. The QTY of items you place in your cart will be the QTY of Boss’s you recieve. For example if you need 15 fittings make sure to add QTY 15 to your cart.
Material: 6061 Aluminum CNC Machined OD(A): 1.00” +/- OD (B): .730” +/- Flange Thickness: .250” +/- Overall Length = 1.00” +/- Installed height= .250” +/- Threads: 5/16-18 / 3/8-16 / 1/2-13 Choose Options Below Tank Hole Cut Size: .730”MIN / 1.00” MAX -This fitting must be welded in -This fitting is threaded blind so there will be no need to seal the threads -This will provide threaded provisions in your assembly perfect for bolting steps, enclosures and other components. - Could be welded to the inside of a tank to provide a perfectly flush threaded fitting that wont leak.
$5.75
|
{ 0 comments }
|
Product # 21029
This Item is sold individually. The QTY of items you place in your cart will be the QTY of Boss’s you recieve. For example if you need 15 fittings make sure to add QTY 15 to your cart. Material: 6061 Aluminum CNC Machined OD(A): .500” +/- OD (B): .375” +/- Flange Thickness: .250” +/- Overall Length = .750” +/- Installed height= .250” +/- Threads: 10-24 / 10-32 / 1/4-20 Choose Options Below Tank Hole Cut Size: .375”MIN / .500” MAX -This fitting must be welded in -This fitting is threaded blind so there will be no need to seal the threads -This will provide threaded provisions in your assembly perfect for bolting steps, enclosures and other components. - Could be welded to the inside of a tank to provide a perfectly flush threaded fitting that wont leak.
$4.75
|
{ 0 comments }
|
Product # 44027 Material = CNC Machined 6061 Aluminum ID = 1.715″ +/- This adapter will thread into an existing female 2″ NPT and allow you to install a 5 bolt fuel level sending unit. Any of our sending units in our “sending unit” section will
$45.00
|
{ 0 comments }
|
Product # 81004 Material = Aluminum ID = 1.970″ +/- NPSM = (NATIONAL PIPE STRAIGHT MECHANICAL)
$22.00
|
{ 0 comments }
|
Product # 81050 Material = STAINLESS STEEL ID = 1.970″ +/- NPSM = (NATIONAL PIPE STRAIGHT MECHANICAL)
$31.00
|
{ 0 comments }
|
Product Number: 27027
Fits Kelch 2-1/4″ Caps
OD of Neck= 2.200″
ID of Neck = 1.75″
Overall height installed= 1.25″
Threads= 5TPI Modified Butress
Hole Cut = 2″ MIN 2.25″ MAX
Aluminum Weld-in Neck ( Steel, Stainless Steel Availible below)
$26.00
|
{ 0 comments }
|
Product # 44030
Material = CNC Machined 6061 Aluminum Overall Length = 3.00″ +/- Overall Diameter = 1.500″ +/- Hole Cut = 1.275″ -0.00 / +.015″ Approx Weight = 2.2 OZ -This Valve will work with water, gasoline or diesel fuel. -Use this valve any time it is important to trap fuel around a pump or pickup tube. -It may be necessary to use multiple valves - if installing this valve into an existing tank you must have access to both sides of the baffle. Examples of use would include but not limited to: -Off Road -Drag Racing -Road Racing -Marine Click video below for demonstration of this product.
$62.00
|
{ 0 comments }
|
PRODUCT # 00BTWW 4.3oz 60% Ring Spun Cotton 40% Polyester Color and Size Options Below T-SHIRTS ARE CURRENTLY ON ORDER AND SHOULD BE RECEIVED MAY 2016.
$20.00
|
{ 0 comments }
|
PRODUCT # BOYD-TIGWELDER 4.3oz 60% Ring Spun Cotton 40% Polyester Color and Size Options Below T-SHIRTS ARE CURRENTLY ON ORDER AND SHOULD BE RECEIVED MAY 2016.
$20.00
|
{ 0 comments }
|
SpinSecure FSS 754 Versalock Vented Female Cap
Product SKU # 81047 Vented = YES Keys Included= YES Connection= 2″ Male required on tank or use # 81048 Adapter This is for the CAP ONLY if you are building an aluminum tank you will need the following additional items. QTY 1) ( SKU # 21009) 2″ NPT Female QTY 1) (SKU # 81048) SpinSecure Male to Male Adapter
$49.50
|
{ 0 comments }
|
PRODUCT # 25017-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$86.04
|
{ 0 comments }
|
PRODUCT # 25017-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$66.56
|
{ 0 comments }
|
PRODUCT # 25017-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$71.43
|
{ 0 comments }
|
PRODUCT # 25017-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$76.30
|
{ 0 comments }
|
PRODUCT # 25017-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$81.17
|
{ 0 comments }
|
PRODUCT # 25017-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = NA Hose Barb= 5/16″ Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 1.25″ or less ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$61.69
|
{ 0 comments }
|
PRODUCT # 25016-24 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 24″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$60.80
|
{ 0 comments }
|
PRODUCT # 25016-30 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 30″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$65.67
|
{ 0 comments }
|
PRODUCT # 25016-36 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 36″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$70.54
|
{ 0 comments }
|
Boyd Welding 2″ Machined Cap & Neck - Weld-in application -Machined From 6061-T6 Aluminum -2″ Pipe Straight Thread 11.5 TPI - Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard *** 4″ Long and 6″ Long Necks are availible, choose option below before adding to cart.***
$49.75
|
{ 0 comments }
|
PRODUCT # 25016-12 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 12″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$51.06
|
{ 0 comments }
|
PRODUCT # 25016-18 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 18″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$55.93
|
{ 0 comments }
|
PRODUCT # 25016-6 MATERIAL: Stainless Steel OD Thread = 1/2″ NPT Male (1/2″ NPT Female Required in Tank) ID Thread = 3/8 NPT Female Tube ID = .325 +/- Minimum Tank Depth = 2″ Maximum Tank Depth = 6″ Screen= NO Overall Installed Height = 3/8″ ***** When installed properly you should leave approx .250″ from the bottom of tank to bottom of pickup tube.
$46.19
|
{ 0 comments }
|
Product # 27046
Kelch Target 350 (VENTED) Cap and Aluminum Machined Neck
Cap:
-Material = Black Plastic
- Threads = 5 TPI Modified AM Butress
-Vented= Yes
-Lanyard = No
Neck:
- Material= 6061 Aluminum CNC Machined
- Threads= 5 TPI Modified AM Butress
- OD = 3.480″ +/-
- ID = 2.750″ +/-
-installed height (neck only) = 1.800″ +/-
Installation:
- MUST BE WELDED IN
- Overall Installed Height W/ Cap = 2.625″ +/-
- Hole Cut Size = 3.250″ +.065 / – Zero
$65.00
|
{ 0 comments }
|
Product # 46005
Replacement SAE 5 Bolt Sending Unit Flange Gasket
Material: BUNA- N
Thickness: .125″ +/-
OD: 2.75″”
ID: 1.525″
x5 bolt pattern on 1.060 Bolt CL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$3.42
|
{ 0 comments }
|
Product # 46004
Replacement Boyd Welding EFI Gasket.
Material: BUNA- N
Thickness: .125″
OD: 6″
ID: 4″
x12 .190 holes on 5″ CL
All gaskets are considered Maitenence Items and are not covered under our 2 YR tank structure warranty. While it may not be always necessary, It is recommended to replace this gasket every 12 months. Failure to do so may result in a leaking sealing surface.
$11.99
|
{ 0 comments }
|
Product Number: 27031
$69.00
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1.25″ Taper Plug W/Pull Ring Product # 74014 Fits Female 1.25″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.42
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1.5″ Taper Plug W/Pull Ring Product # 74015 Fits Female 1.5″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.54
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1″ Taper Plug W/Pull Ring Product # 74013 Fits Female 1″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.42
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/2″ Taper Plug W/Pull Ring Product # 74011 Fits Female 1/2″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.24
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 3/4″ Taper Plug W/Pull Ring Product # 74012 Fits Female 3/4″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.30
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 3/8″ Taper Plug W/Pull Ring Product # 74010 Fits Female 3/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.24
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/8″ Taper Plug W/Pull Ring Product # 74009 Fits Female 1/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.18
|
{ 0 comments }
|
QTY 10 Minimum Order , NON Returnable , NON Refundable Product 1/8″ Taper Plug W/Pull Ring Product # 74008 Fits Female 1/8″ NPT Fittings THIS PRODUCT IS FOR PROTECTION OF THREADS DURING SHIPPING, INVENTORY STORAGE AND IS INTENDED FOR SINGLE USE THEN DISCARD. UNDER NO CIRCUMSTANCES SHOULD THESE EVER BE USED WITH ANY TYPE OF FUELS
$0.18
|
{ 0 comments }
Product # 21056 Material: 6061 Aluminum OD: 3" +/- ID: 2" +/- Flange Thickness: .250 Threads: UNF 10-32 Bolt Centerline: 6 x 2.375" CL Tank Hole Cut Size: 2.625" This Flange Fits most 6 bolt sending unit's usually found on british made vehicles IE: Morgan , Triumph , MG, ETC.
$18.25
|
{ 0 comments }
|
Product # 21057 Material: 6061 Aluminum OD: 2.5″ Installed Height: .875″ +/- Hole Size Needed: 2.25″ Fitting Threads: 1/4″ NPT Finish: Natural Machined Finish ** This sump must be welded into an aluminum tank only
$41.00
|
{ 0 comments }
|
Product # 27036 Cap and Neck included NECK: Material: Aluminum OD: Approx 2.375″ ID: Approx 1.75″ Threads : 2.25″ – 5 TPI Modified Butress Hole Cut : 2″ Overall Height with cap installed: 2.680″ Lanyard Length: Internal 8″
$49.00
|
{ 0 comments }
|
Product # 32008 Material: Aluminum 6061-T6 Machined Hose Size: 5/8″ Overall Lenght: 3″ Ouside Diameter: Approx 1″
$75.00
|
{ 0 comments }
|
Product # 44024 Material: Aluminum 6061-T6 Machined Dimensions Outside: 3 x 2 x .75 without fitting Thread: 3/8 NPT Weldable: YES
$29.00
|
{ 0 comments }
|
Ford F Series Weld-in OEM Vent Bung Aluminum Bung Only (OEM Vent Picutred-Not Included)
$24.99
|
{ 0 comments }
|
Product # 44022 Material: 6061 t-6 Aluminum OD: 6″ ID: 4.375″ Installed Height: .875″ Hole Cutout: 5.75″ Threads: 1/4-20 Blind Tapped Gasket: YES MUST BE WELDED IN
$59.00
|
{ 0 comments }
| 3 Port 1/2″ NPT Threaded Flange Machined from 6061 Aluminum Installed height .875″ Overall Dimensions 4.5″ x 4.5″
$35.00
|
{ 0 comments }
| 2 Port 1/2″ NPT Threaded Flange Machined from 6061 Aluminum Installed height .875″ Overall Dimensions 2″ x 4.5″
$28.50
|
{ 0 comments }
|
PRODUCT # 24011 Material = 6061 T-6 Aluminum Hole size = 9/16″ Slot Sold in Packs of QTY 4 These tabs are machined from a solid block of aluminum.
$88.00
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
| Boyd Welding 2″ Machined Knurled Cap & Neck
-Machined From 6061-T6 Aluminum -2″ Pipe Straigh Thread 11.5 TPI - NON Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard
Regular Price:
Special Price: |
{ 0 comments }
| Boyd Welding 2″ Machined Cap & Neck
-Machined From 6061-T6 Aluminum -2″ Pipe Straigh Thread 11.5 TPI - NON Vented - Length of Neck = 2″ - Gasket Included - 8″ internal lanyard
Regular Price:
Special Price: |
{ 0 comments }
|
Product # 26007 Material= CNC Machined from 6061-T6 Aluminum OD= 3.625″ Installed Height= .875″ Hole size Needed= 3.375″ Fitting Threads= 1/2″ NPT Finish= Natural Machined Finish ** This sump must be welded in to an aluminum tank only**
$65.00
|
{ 0 comments }
|
Product # 27040 Material: 6061 Aluminum Cap: Vented: NO OD: 1.625″ ID: 1.25 Threads per inch: 14 Gasket: Buna-N O-Ring Included Neck: OD: 1.312″ ID: 1″ Length: 3″
$31.00
|
{ 0 comments }
| Gas Spring for toolbox lid. Approximate total length 9 inches.
Includes 2 mounting tabs.
$20.00
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
|
Product # 29009 Material: 6061 Aluminum Bolt Circle: 3.5″ CL x 6 places Hole opening: 2.500″ Threads: 8 Threads Per Inch Includes: Gasket, 8″ internal Lanyard, 6 SS Screws, Under Mounting Ring. -This Cap and neck assembly can be mounted to any type of tank material including Steel, Aluminum And Plastic.
$96.00
|
{ 0 comments }
|
Product Number: 11021 Tank Dimensions: 24 x 14 x 12 Fill Cap: Non Vented Threaded Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Pictures show product with sending unit installed. Sending Unit Purchased Seperate
$219.00
|
{ 0 comments }
|
Boyd Product # 37002 Gates Product # 27344 ID = 1/4″” EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
Regular Price:
Special Price: |
{ 0 comments }
|
Boyd Product # 37004 Gates Product # 27346 ID = 3/8″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.78
|
{ 0 comments }
|
Boyd Product # 37003 Gates Product # 27345 ID = 5/16″ EPA Certified = YES For Fuel Injection = YES -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$3.33
|
{ 0 comments }
|
Boyd Product # 37005 Gates Product # 27323 ID = 1/4″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.65
|
{ 0 comments }
|
Boyd Product # 37007 Gates Product # 27325 ID = 3/8″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$2.05
|
{ 0 comments }
|
Boyd Product # 37006 Gates Product # 27324 ID = 5/16″ EPA Certified = YES For Fuel Injection = NO -This Product is Sold By the Foot. Choose how many feet you need by entering the QTY EXAMPLE: If you need 15 FT enter QTY 15 -Full spool lengths are 250 ft
$1.85
|
{ 0 comments }
|
Boyd Product # 37011 Gates Product # 23924 ID= 1.5″ OD= 2″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$67.14
|
{ 0 comments }
|
Boyd Product # 37013 Gates Product # 23936 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$84.69
|
{ 0 comments }
|
Boyd Product # 37012 Gates Product # 23932 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = YES Steel Wire Reinforced This product is sold in stock lengths only.
$77.55
|
{ 0 comments }
|
Boyd Product # 37014 Gates Product # 23964 ID= 1.5″ OD= 2″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$47.64
|
{ 0 comments }
|
Boyd Product # 37015 Gates Product # 23972 ID= 2″ OD= 2.375″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$59.94
|
{ 0 comments }
|
Boyd Product # 37016 Gates Product # 23976 ID= 2.25″ OD= 2.625″ Stock Length = 3 FT Bendable = NO This product is sold in stock lengths only.
$68.34
|
{ 0 comments }
|
Boyd Product # 37017 Gates Product # 24710 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37018 Gates Product # 24712 ID = 2″ OD= 2.375″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$33.43
|
{ 0 comments }
|
Boyd Product # 37019 Gates Product # 24713 ID = 2.25″ OD= 2.625″ LEG A= 7″ LEG B= 7″ Bend= 45 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37020 Gates Product # 24715 ID = 1.5″ OD= 2″ LEG A= 7″ LEG B= 7″ Bend= 90 DEG
$26.63
|
{ 0 comments }
|
Boyd Product # 37022 Gates Product # 24718 ID = 2.25″ OD= 2.625″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$38.05
|
{ 0 comments }
|
Boyd Product # 37021 Gates Product # 24717 ID = 2″ OD= 2.375″ LEG A= 6″ LEG B= 6″ Bend= 90 DEG
$33.43
|
{ 0 comments }
| Product Number: 13014
*Please Note: Our website does not reflect current stock levels.
$1,675.00
|
{ 0 comments }
| Product # 42003
The EZ-8 Pump is ideal for on-the-go fueling. This 12-volt DC fuel pump delivers 8 GPM, equivalent to standard gas stations. The system comes complete with power cord, manual unleaded nozzle, three-piece, trim-to-fit suction pipe and 10 ft of 5/8 in. hose.
$295.00
|
{ 0 comments }
| Product Number: 11016 500 Gallon 3/16 Aluminum tank Heavy Duty Steel Skid w/ Crane hooks 2 Internal Baffles Fully Welded Inside and Fully TIG Welded Outside -BUILT TO LAST Please Call For Freight Quotes: 352-447-2405
$4,625.00
|
{ 0 comments }
| Product Number: 13016
*Please Note: Our website does not reflect current stock levels.
$1,050.00
|
{ 0 comments }
| Product Number: 13004 Pump Included *Please Note: Our website does not reflect current stock levels.
$765.00
|
{ 0 comments }
| Product Number: 37001 Sold in 1 FT Increments 25′ in a case Call for Case Pricing!
$3.75
|
{ 0 comments }
|
Product Number: 11002 Tank Dimensions: 8 x 6 x 6 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$89.00
|
{ 0 comments }
|
Product Number: 32001 Threads: 1/2″ NPT Hose Barb: 5/16″ Material: Brass Q: What is the Roll Over Safety Vent? Do i need it? A: The Rollover Safety Vent is a simple ball check valve device that will allow the tank to vent when in the normal operating position and also act as a Anti-Splash when your tank is full. In the event of an accident causing a rollover the ball will drop and block off the vent port so that fuel does not leak out. For safety I would always recommend purchasing the Rollover Safety vent
$31.00
|
{ 0 comments }
|
Product Number: 11011 Tank Dimensions: 18 x 12 x 12 Fill Cap: Flush Aircraft Style Fill * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$179.00
|
{ 0 comments }
|
Product Number: 11009 Tank Dimensions: 12 x 12 x 21 Fill Cap: Flush Aircraft Style Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$199.00
|
{ 0 comments }
| Product Number: 27018 Aluminum NON- Vented Cap Key Locking Aluminum Neck Must Be Welded in
$68.00
|
{ 0 comments }
| Product Number: 13001
*Please Note: Our website does not reflect current stock levels.
$399.00
|
{ 0 comments }
|
Product Number: 11014 Tank Dimensions: 24 x 18 x 12 Fill: 2″ Ribbed for Hose Pipe * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$249.00
|
{ 0 comments }
| Product Number: 27030 3″ NON Vented Cap Key Locking Aluminum Neck Must Be Welded In
$75.00
|
{ 0 comments }
|
Product Number: 13003 Tank Dimensions: 48 x 18 x 10 Fill Cap: 2″ NON Vented Threaded Cap P# 27017 * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$429.00
|
{ 0 comments }
|
Product Number: 11004 Tank Dimensions: 12 x 12 x 8 Fill: 1.5″ OD Pipe * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$99.00
|
{ 0 comments }
|
Product Number: 11005 Tank Dimensions: 10 x 10 x 16 Fill Cap: Flush Aircraft Style Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$159.00
|
{ 0 comments }
| Product Number: 13008
*Please Note: Our website does not reflect current stock levels.
$750.00
|
{ 0 comments }
| Product Number: 14017 Aeromotive In-Tank A-1000 Pump Approx 19 Gallons SUPPORTS 1200+ HP Shown With optional Rollover vent and Sending Unit. *Please Note: Our website does not reflect current stock levels.
$898.00
|
{ 0 comments }
|
Product Number: 14004 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Tank Dimensions: 26.5 x 19 x 10
$648.00
|
{ 0 comments }
|
Product Number: 14003 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Tank Dimensions: 26.5 x 19 x 10
$648.00
|
{ 0 comments }
|
Product Number: 14001 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 26.5 x 19 x 10 **Scroll down for FAQ on this product.
$349.00
|
{ 0 comments }
|
Product Number: 14002 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 26.5 x 19 x 10 **Scroll down for FAQ on this product.
$349.00
|
{ 0 comments }
|
PRODUCT # 29001 This Package Saves 15% Off Individual Retail Prices Package Contents:
Regular Price:
Special Price: |
{ 0 comments }
|
Product Number: 14011 Will only replace ford part # (6C3Z9002F) Customer is responsible for confirming this. Boyd Welding will not pay for return shipping. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$638.00
|
{ 0 comments }
|
Product Number: 14005 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$282.00
|
{ 0 comments }
|
Product Number: 14006 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$581.00
|
{ 0 comments }
| Product Number: 14008 Fits in stock location Does not hang down any further than stock tank Approx 20 gallons Aeromotive In-Tank Pump Included *Please Note: Our website does not reflect current stock levels.
$789.00
|
{ 0 comments }
|
Product # 41004 Kit includes: *Our Brackets are not adjustable we fabricate each bracket based on your tank depth. Below you will need to choose the correct bracket length for your tank. The bracket length should be at minimum 1″ less than the depth of your tank. See below examples. EXAMPLE: 12″ deep Tank = 11″ Bracket length. Min/Max Bracket length = 6″ / 20″
$349.00
|
{ 0 comments }
| Product # 14019
Direct Replacement Aluminum Tank Our website does not reflect current stock levels. Please allow 7 business days for fabrication and shipment. Are you a Dealer? if so We offer wholesale pricing and bulk discounts. Please call for more information
$575.00
|
{ 0 comments }
| Product # 14014
Tank construction: .125 5052 aluminum *Please Note: Our website does not reflect current stock levels.
$750.00
|
{ 0 comments }
|
Product Number: 11001 Tank Dimensions: 8 x 6 x 4 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$79.00
|
{ 0 comments }
|
Product Number: 11010 Tank Dimensions: 18 x 12 x 12 Fill Cap: NON Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. Alternate Pictures Shown With Optional 2″ Threaded Cap and Rollover Safety Vent
$159.00
|
{ 0 comments }
|
Product Number: 11012 Tank Dimensions: 30 x 12 x 12 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$259.00
|
{ 0 comments }
|
Product Number: 11003 Tank Dimensions: 8 x 8 x 12 Fill Cap: Flush Mount Aircraft Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$129.00
|
{ 0 comments }
| Product Number: 27016 NON- Vented Cap Key Locking Aluminum Neck Must Be Welded in
$76.00
|
{ 0 comments }
|
Product Number: 13018 Tank Dimensions: 40 x 10 x 18 Fill Cap: 2″ Full Function Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$347.00
|
{ 0 comments }
|
Product Number: 11019 Tank Dimensions: 24 x 12 x 18 Fill Cap: NON Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$249.00
|
{ 0 comments }
| 25 Gallon Gasoline Tank 15 Gallon Mix fuel Tank Integrated Hose Wraps Product # 14016 *Please Note: Our website does not reflect current stock levels.
$2,150.00
|
{ 0 comments }
|
Product Number: 11020 Tank Dimensions: 26 x 16 x 16 Fill Cap: Non Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$290.00
|
{ 0 comments }
|
Product Number: 11017 Tank Dimensions: 12 x 8 x 8 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$89.00
|
{ 0 comments }
|
Product Number: 13002 Tank Dimensions: 48 x 10 x 18 Fill Cap: 2″ Threaded NON Vented Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$429.00
|
{ 0 comments }
| Product # 13023
Each Fuel trailer is custom built per your requirements. Please call or email with your list of requirements and a quote can be provided.
$6,900.00
|
{ 0 comments }
|
Product Number: 11006 Tank Dimensions: 12 x 12 x 8 Fill Cap: NON-Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$109.00
|
{ 0 comments }
|
Product Number: 11018 Tank Dimensions: 12 x 8 x 12 Fill Cap: Vented Twist Cap * Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$106.00
|
{ 0 comments }
|
Product # 13020 Our website does not reflect current stock levels. Please allow 7 – 10 business days for fabrication and shipment. * Fits Below Bed Rails / Bed Covers * MAX Dimensions = 56.375″ L x 20″ W x 19″ H Tank Features: Toolbox Features: Scroll down for more details
$998.00
|
{ 0 comments }
| Product Number: 13007 Fits most trucks with roll up bed cover *Please Note: Our website does not reflect current stock levels.
$575.00
|
{ 0 comments }
|
Product Number: 14026 * Pictures show Rollover Safety Vent and Sending Unit Options installed. *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products. -Tank Dimensions: 28 x 20 x 10 **Scroll down for FAQ on this product.
$369.00
|
{ 0 comments }
| Product # 14023
Tank Gallons = Approx 25 Includes:
$487.00
|
{ 0 comments }
| Product # 13012
Tank Dimensions: 52 x 26 x 16 *Please Note: Our website does not reflect current stock levels.
$975.00
|
{ 0 comments }
|
Product # 29002 This Package saves you 15% off retail pricing Package includes:
Regular Price:
Special Price: |
{ 0 comments }
| Welcome to the Build your own Transfer Tank Page. Picture shown is for fitting location reference only. Fill Cap, Fittings and mounting tabs are fixed locations and cannot be moved. Be sure to measure your vehicle before you order. Included items are 27017 NON vented cap, 32001 Rollover Safety Vent, QTY (3) 1/2″ NPT fittings and mounting tabs. This form is designed to provide instant pricing on a generic tank. If you need something custom We can do it just email us a completed drawing or sketch.
$316.00
|
{ 0 comments }
| Product Number: 14012 15 Gallons *Please Note: Our website does not reflect current stock levels.
$199.00
|
{ 0 comments }
| 15 Gallon Replacement Tank Kelch Neck – Re-use your cap. Fits Model # 580.325601 *Please Note: Our website does not reflect current stock levels.
$199.00
|
{ 0 comments }
|
Product Number: 14013 Tank Dimensions: 40 x 9.5 x 10 *Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
$789.00
|
{ 0 comments }
|
Product Number: 14030 Tank Dimensions: 46.5 x 6.5 x 10 Fill: 2″ OD Ribbed For Hose This product includes the Aeromotive Stealth 340 In-Tank Pump System.
* Please Note: Our website does not reflect current stock levels. Please Allow 5-7 Business days for fabrication on most products.
Regular Price:
Special Price: |
{ 0 comments }
| Product Number: 14007 Fits in stock location Does not hang down any further than stock tank Approx 20 gallons *Please Note: Our website does not reflect current stock levels.
$490.00
|
{ 0 comments }
|
Product # 13017 • 185 Gallons Diesel Fuel
$4,500.00
|
{ 0 comments }
-Brass 90 degree NPT
-Will not corrode threads
{ Comments on this entry are closed }
-Standard connection used for most marine and truck application.
-Will not corrode threads
Shop Online
More Info…
{ 0 comments }
